Dukane iQ Series Bedienungsanleitung Seite 26
- Seite / 116
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
iQ Series, Automation-Controlled Probe Generators LS User’s Manual
Page 18 Dukane Manual Part Number 403-572-03
CAUTION
The power cord is equipped
with a three-prong,
grounded-type plug for
your safety. Whenever a
two-slot receptacle is en-
countered, we strongly
recommend that it is replaced with a
properly grounded three-lead receptacle.
Have a qualied electrician do the replace-
ment in accordance with the National
Electrical Code and local codes and or-
dinances. DO NOT cut off the power cord
grounding prong or alter the plug in any way.
Connecting Cables
(Quick Start Guide)
The connections are the same for both the vertical and
horizontal generator congurations. However, the panel
location of the connectors differs between the two chassis
styles. Details about the various system connectors and
their pin assignments are covered in Section 4.
Manually Operated Probe System
(Hand Probes)
1. Ground the generator chassis with a user–supplied
14-Gauge wire and attach it to the grounding stud A in
Figure 3 - 6.
2. Attach the hand probe’s HD - 15 system input connec-
tor to J2 on the I/O panel. B in Figure 3 - 6.
3. Attach high-voltage coaxial cable to J1, the ultrasound
output connector. C in Figure 3 - 6.
4. Power cords with an IEC connector are supplied
with the standard horizontal bench and vertical panel
mounted systems. Connect the AC power cord to the
IEC power inlet connector on the ultrasonic generator
(D in Figure 3 -6), and plug the other end into an ap-
proved AC outlet.
NOTE
Horizontal bench generator is shown for
reference. Vertically mounted units use the
same connections, but those connections
have a different orientation.
(See Figure 4 -1.)
Figure 3- 6 Horizontal Bench Generator with Hand Probe Cable Connections
20HB120
LINE VOLTAGE:
200-240 Vac
50/60Hz, 15A
PE
CANCEL
ENTER
ONLINE
OFFLINE
TEST
INFO
AC POWER
INLET
GROUNDING
STUD
J7
J7 is optional.
ULTRASOUND OUTPUT
OUTPUTS
INPUTS
J2
J3
J4
J1
I
0
- User’s Manual 1
- Revision History 3
- Contents 5
- Continued 6
- SECTION 1 9
- Page left intentionally blank 10
- General User Information 11
- Generator Overview 12
- Key Generator Features 12
- SECTION 2 13
- General Considerations 15
- Plastics Health Notice 16
- Electrical Safety 16
- Domestic Power Grounding 17
- International Power Grounding 17
- Lifting the Equipment 18
- SECTION 3 19
- Before Installation 21
- Lockout/Tagout 22
- Unpacking 23
- Horizontal Bench Chassis 24
- RFI Grounding 25
- Connecting Cables 26
- Power Cords 27
- SECTION 4 29
- Panel Layout Overview 31
- LINE VOLTAGE: 32
- 200-240 Vac 32
- 50/60Hz, 15A 32
- AC Power Inlet Panel 33
- System I/O Panel 34
- 1 2 3 4 5 35
- 11 12 13 14 15 35
- System Outputs Connector 37
- (+22V Power Supply) 38
- (+22V Power Ground) 38
- (Any Fault Status Output) 39
- (Suspect Part Status Output) 41
- (Isolated Common) 41
- (Not Used) 41
- Ultrasound Output Connector 41
- Conguration Port Connector 41
- SECTION 5 43
- Control Panel and Display 45
- Overview 45
- Display Controls 46
- LCD Display 47
- Power Output Level Scale 47
- System Operating Mode Keys 47
- INFO Key 48
- Status LEDs 49
- System Parameter Settings 50
- Section 6 51
- Programming Examples 54
- SECTION 7 57
- System Verication Tests 59
- System Test 60
- Probe Operation 61
- Stop Ultrasound Output 62
- SECTION 8 63
- No Ultrasonic Output 65
- INFO Status LED: RED 66
- Welding Problems 67
- SECTION 9 69
- Display/Control Panel 71
- Air Ventilation Slots 72
- I/O Connector 72
- AC Power Cord 72
- SECTION 10 73
- Power Inlet Options 75
- 120 volt line cord 76
- I/O Panel Options 77
- Option Panel Modules 78
- MPC Probe Control 79
- (6 PLCS) 80
- Rear Connections 81
- Front Connections 81
- E in Figure 10 - 9) 82
- MPC Interface Status LEDs 82
- MPC Cycle Flow Chart 83
- Part Number - 110- 4183 84
- Part Number - 110- 4397 85
- NPN TO PNP CONVERSION 86
- PNP TO NPN CONVERSION 87
- +5V TO +24V PNP CONVERSION 88
- 110-4397 88
- RS-232 Interface Option 89
- Part Number - 110-4554 90
- EtherNet/IP 91
- SECTION 11 93
- OPTIONAL 95
- FRONT RACK MOUNTING 95
- .220 DIA. SLOTS 96
- [5.59] (4 PLCS) 96
- Operating Environment 97
- Weight: 97
- AC Power Requirements 98
- System Process Controls 99
- Regulatory Agency Compliance 100
- SECTION 12 101
- Contacting Dukane 103
- APPENDICES 105
- List of Figures 107
- List of Figures continued 108
- List of Tables 109
- Page 103 111
- Continued 112
- Dukane ISO 115
- Part No. 403 116
Verwandte Produkte und Handbücher für Netzteile Dukane iQ Series
Netzteile Dukane iQ Series Bedienungsanleitung
(144 Seiten)
(144 Seiten)
Netzteile Dukane iQ Series Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Netzteile Dukane iQ Series Bedienungsanleitung
(76 Seiten)
(76 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.750 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern